COTRUST CPU Master Module Basic CPU H224 (214-1BA33-0X24)
Basic CPU H224: 12KB program space / 8KB data space, 220VAC power supply, 14DI/10DO relay output, 2A, 1 PPI, 1 free communication port, 1 Ethernet communication port, no support for modules and expansion cards


CTH2 214-1BA33-0X24



technical parameter

Physical characteristics

Size (width × height × depth)
137×80×62mm


Power consumption
7W


Memory characteristics

Program memory
8KB+4KB


Data memory
8KB


General characteristics

Total number of timers
1ms
10ms
100ms


256


4


16


236


Total number of counters


256


Memory memory bit


256


Memory storage bit power-down retention time


Permanently


Sequence control relay (S)


256 bits


Time interruption


2 1ms resolution


Edge break


4 rising edges and / or 4 falling edges


Analog potentiometer


no


Boolean operation execution time


0.22μs


Floating point execution time


12μs


clock


Built-in, accuracy ±120s/m


BD expansion board interface number


no


System indicator


3, STOP, RUN, SF


RUN/STOP dialing code


Yes, 2 states


Programming card


stand by


storage card


not support


Rated input voltage


DC24V


power supply


Native +5V


+24V


 


660mA


200mA


Integrated communication function


Communication Interface


2 communication ports:


PORT0: PPI communication port, RS485


FPORT: free communication port, RS485


PPI baud rate (baud)


9.6k, 19.2k and 187.5k


Free port baud rate (baud)


1.2k ~ 115.2k


Maximum cable length per segment


      Use an isolated repeater


      Isolation repeater not used


 


The baud rate is 1000 meters at 187.5 and 1200 meters at 38.4k.


50 meters


Maximum number of sites


32 stations per segment, 126 stations per network


Maximum number of primary stations


32


Physical interface


2 RS485 interfaces


isolation


Not isolated


Ethernet communication function


Communication Interface


1 standard Ethernet port


Communication standard


Comply with IEEE802.3 standard


transfer speed


10Mbps and 100Mbps adaptive


Adaptive cross connect


not support


Interface to Industrial Ethernet (10/100Mbps)


RJ45 socket


agreement type


UDP/TCP protocol


Supports MICO Ethernet programming and supports Ethernet communication between PLCs.


Configuration method


Support the host computer to search the PLC through the network port, and support the network port to download the system configuration.


Maximum number of connections


Each PLC supports up to 8 UDP connections and supports up to 4 TCP connections.


Maximum number of IT connections


8 UDP_PPI connections, 4 of which are 4 and 4 are.


4 ModBus_TCP connections, 2 master stations and 2 slave stations.


Number of user data


Up to 200 bytes are used for TCP/IP transmission.


Up to 240 bytes are used for ModBus_TCP transmission.


port


Local: 1~65535


Remote server: 8888


Start time or restart time after reset


About 3 seconds.


Indicator light


Green RMC indicator: On: Remote control is in effect, Off: Remote control is invalid.


Green Ethernet indicator: On: Connection, blinking: Transmission; Off: Not connected


Maximum cable length per segment


100m


isolation


Communication port isolation


I/O characteristics


Local digital input points


14


Input type


Sink/source


Local digital output points


10


Output type


Relay dry contact


Digital I/O image area


128DI/1280DQ (excluding CAN communication dedicated image area)


Analog I/O image area


32AI/32AQ (excluding CAN communication dedicated image area)


Maximum number of I/O modules allowed


no


Maximum digital I/O configuration


IO: 256 (128 input / 128 output)


Maximum analog I/O configuration


64 (32 input / 32 output)


Pulse capture input


14


High speed counter


    total


    Single phase counter


    Two-phase counter


 


4


4×50KHz


1×30KHz


Digital input characteristics


This machine integrates digital input points


14


Input type


Sink/source


Rated voltage


24V DC


Maximum continuous allowable voltage


20.4-28.8V DC


Surge voltage


35V DC for 0.5s


Logic 1 signal (minimum)


Logic 0 signal (maximum)


15 VDC, 2.5 mA


5 VDC, 1 mA


Maximum allowable leakage current


1mA


Input filtering


Support 3.4ms and 6.4ms


Isolation (site and logic)


500V AC, 1 minute


Simultaneous input


14


Maximum cable length


shield


Unshielded


500 meters (standard input)


50 meters (high speed counter input)


300 meters (standard input)


Digital output characteristics


This unit integrates digital output points


10


Output type


Dry contact


Rated voltage


24V DC or 110V/220VAC


Output voltage range


5~30VDC: 5~250VAC


Logic 1 signal (minimum)


-


Logic 0 signal (maximum)


-


Current rating per point


2A


Rated current per common


8A


Leakage current (maximum)


-


Surge current (maximum)


7A, contact closed


Lamp load (maximum)


30W DC/200W AC


On resistance (contact)


0.2Ω


Isolation (site and logic)


-


Delay


Disconnected to: -


Connected to disconnected:-


Contact life at rated load


100,000 on and off


Simultaneously turned on output


All output points


Two outputs in parallel


no


Maximum cable length


shield


Unshielded


500 meters


150 meters
发送反馈
历史记录 TAG：